﷫޹˾
֤ͨ ENGLISH| İ |
˾֤ϵ Ʒ Ŷ̬зϵ ҳ
ҪƷ

ԸԷϢҷϢ

ѹȦ

ѹȦ
Drawn Cup Needle Roller Bearings ѹȦ
ѹȦ˾ͳƷеȦñְ徫ܳѹεģṹռСҾнϴ󸺺ڰװռܵƺͿײΪijϡѹ׺󲻱ؽһλ

ѹȦST14ְ徫ܳѹβ̼ص߶ȼСҾмǿغø߸ԱּG2״Ȧʹõƽߣ

еȦþϣҪ̶װáʹڸٴ󸺺£Ҳֱܳйܡ⣬֬ݻ󣬿ɳڲ֬Ҳܱ֤гת豸ת

HK

ͳѹȦ

HK...RS

ͳѹȦУܷ

HK...2RS

ͳѹȦУ˫ܷ

BK

ͳѹȦ

BK...RS

ͳѹȦУܷ

MF

ͳѹȦУͷ

MFY

ͳѹȦУƽͷ

F

ͳѹȦУͷ

FY

ͳѹȦУƽͷ

SCE

ͳѹȦУӢϵ

BCE

ͳѹȦУӢϵ

ߴ غ ת
Shaft Open end Closed end Dimensions Basic Load Ratings Limiting
Diameter ܷͺ ˫ܷͺ ܷͺ Fw D C C1 C2 r Cr Cor Speed
Designation Mass Designation Mass Designation Mass Dynamic Static
with Sealed with Sealed with Sealed
mm on one side g on both sides g g min. min. kN kN rpm
10 HK1012 RS 4.5 HK10142RS 4.6 BK1012RS 4.6 10 14 12 14 9.3 0.4 4.4 5.1 17000
12 HK1214 RS 10.0 HK12162RS 11.0 BK1214RS 11.5 12 18 14 16 11.3 0.8 6.5 7.3 14000
14 HK1414 RS 12.0 HK14162RS 13.0 BK1414RS 13.0 14 20 14 16 11.3 0.8 7.1 8.5 12000
15 HK1514 RS 12.0 HK15162RS 14.5 BK1514RS 14.5 15 21 14 16 11.3 0.8 7.8 9.8 11000
HK1518 RS 16.0 HK15202RS 18.0 BK1518RS 18.0 15 21 18 20 15.3 0.8 10.5 14.4 11000
16 HK1614 RS 13.0 HK16162RS 15.0 BK1614RS 15.3 16 22 14 16 11.3 0.8 7.6 9.7 11000
HK1618 RS 14.5 HK16202RS 17.0 BK1618RS 17.5 16 22 18 20 15.3 0.8 8.9 11.3 11000
18 HK1814 RS 14.0 HK18162RS 15.0 BK1814RS 16.0 18 24 14 16 11.3 0.8 8.1 10.9 9500
20 HK2014 RS 17.0 HK20162RS 19.0 BK2014RS 20.0 20 26 14 16 11.3 0.8 8.6 12.1 8500
HK2018 RS 21.5 HK20202RS 23.5 BK2018RS 24.5 20 26 18 20 15.3 0.8 12.7 20.1 8500
22 HK2214 RS 16.0 HK22162RS 18.0 BK2214RS 19.0 22 28 14 16 11.3 0.8 9.1 13.4 8000
HK2218 RS 24.0 HK22202RS 26.0 BK2218RS 27.0 22 28 18 20 15.3 0.8 13.4 22.1 8000
25 HK2514 RS 26.0 HK25162RS 27.0 BK2514RS 28.0 25 32 14 16 11.3 0.8 11.0 15.2 7000
HK2518 RS 29.0 HK25202RS 31.0 BK2518RS 34.0 25 32 18 20 15.3 0.8 15.6 24.0 7000
30 HK3018 RS 37.0 HK30202RS 39.0 BK3018RS 40.0 30 37 18 20 15.3 0.8 17.2 29.0 6000
35 HK3518 RS 39.0 HK35202RS 41.0 BK3518RS 43.0 35 42 18 20 15.3 0.8 18.7 33.5 5000
40 HK4018 RS 45.0 HK40202RS 48.0 BK4018RS 50.0 40 47 18 20 15.3 0.8 20.0 38.5 4500
45 HK4518 RS 50.0 HK45202RS 54.0 BK4518RS 56.0 45 52 18 20 15.3 0.8 21.3 43.0 4000
˵
1.лغɡתٺѡοá
2.еıּƳɣͺźTN¶ȣ120180ڡ
3.֬ʱתΪֵ60%
Note:
1.These load, speed and mass is reference of choice only.  
2.If the cages are made of plastics, suffix "TN" is added to the bearing No.,the maximum allowable 
  working themperrature is 120 in continuous working and 180 in short working.
3.With grease lubrication, 60% of these limiting speed will apply.

 


ءַ ʡţҵ 绰: 0519-81855361 棺 0519-86305255 Emailyfbearing@sohu.com
Copyright 2008-2010 All rights reserved
Ʒ:,֧й,߹,Ӣƹ,˨,,ˮ,ֹ,,Խ,ˮ,,ƽ,ѹȦ,ʵȦ,͹,,Բ,뱣ּ,֧Ź,,Ϲ,ֱ